Photoshop in Black and White
David Peters
Black and white photography has always been powerful and it has stood the test of time, even against its contemporary color counterpart. When working with black and white, you must incorporate a different set of rules and techniques. With the lack of color the balances of shape and contrast are made to work harder in order to convey the story or set the mood. However, once this is achieved it is striking.
Many digital cameras come equipped with a black and white mode. If yours does not, you can still achieve the black and white look through editing techniques. Photoshop has made this process possible with a vast selection of methods to convert a color photograph into what Photoshop refers to a grayscale, or to us, black and white. Most photographers would agree that it is actually easier while behind the lens to shoot in color and to convert to black and white at another step. The level in control of effects throughout the Photoshop program are much greater than what could be achieved through the actual shot.
The simplest way of converting color to black and white is to change the mode to grayscale (Image > Mode > Grayscale). While this can work, there are other methods. Let's take a look at three other alternatives that will convert color to grayscale (black and white):
Desaturation is the first method.. This is the elimination the observable color information while keeping the RGB status of the file. This would permit you to add a tint at a later time without having to change color mode again. Follow Steps: Image > Adjustments > Desaturate (or press Ctrl/Cmd + Shift + U).
A downside of desaturation is the potentially a flat, uninspiring copy of the original. Improve this mentally dividing the picture into parts and following these steps. With this you can increase textures in one area by darkening the shadows and midtones, or increase contrast in another to remove haziness. Take a feathered section to work with and press Ctrl/Cmd + J to copy and paste the selection to a new layer. Add a 'Levels Adjustment Layer' to it, combining the two layers as a clipping mask. Drag the Black and Gray point markers toward the right to bring out texture or to the left to decrease. If you see a dividing line ater making the Levels adjustment, remove by adding a layer mask to the newly made level (set to Reveal All) and paint on the mask in black until the edge disappears using a soft brush at a low opacity setting.
While a Levels adjustment layer would add contrast, a different method would be: Follow Steps: Layer > New Adjustment Layer > Curves This will add a Curves adjustment layer to the background layer. Apply the curve shown to increase midtone contrast, but at slight decrease to the highlights and shadows, however this lessens the haziness effect.
Combine Red and Green Channels to achieve a slightly less dramatic result, using the Multiply blend mode. The difference is subtle, but it shows the fine control you have in this technique. Along with the idea of mixing and calculating channel values, another option called Channel Mixer. This allows the mixing of values of each of the channels, allowing a wide range of combinations. To do this make sure the RGB composite channel is active, and go to Image > Adjustments > Channel Mixer. Enable the Monochrome checkbox. If you change the percentage values for each of the Red, Green, and Blue channels, it will dramatically affect the image.
After choosing the filter effect you desire, use this keyboard shortcut sequence to make it into a new document: Ctrl/Cmd + A (selects all) Ctrl/Cmd + C (copies the selection to the clipboard) Ctrl/Cmd + N (creates a new document of the same proportions as whatever we have on the clipboard. The document will also be a grayscale as we only have one channel selected) Enter/Return (to confirm the settings. No changes are necessary) Ctrl/Cmd + V (to paste the contents of the clipboard to a new layer) You can then use Levels and Curves to fine-tune the result.
Use this method to custom set the levels in each color channel is the preset configuration effects are not what you are looking for in the change of tones or strength of color effects. Pick the channel that works best and keep it active. Go to Image > Calculations. If the Blue channel was active, the Blue channel will be in the Calculations dialog box. Source 1 and 2 are set to the same document, layer, and Blue channel, meaning they will all be combined for the calculation to take place. Set the blending drop-down to Multiply, working in the same way as the normal layer blend methods. Multiply will darken the image, but based on the blue channel. As a result red elements or elements with a red cast will become darker than other elements. Set the Result drop-down box to New Document to create a new multichannel file based on the calculated result.
About the Author:
|
